Doors and drawer fronts go to a filtered shop booth and come back with an even, level, factory-looking finish. Boxes are sprayed in the kitchen behind sealed containment, in thin coats, with a light sand between each one.
Spraying is the default here rather than an upgrade. A brush or roller is only used where a small area of trim cannot be masked cleanly. Kitchens in Blue Grass Meadows and Rolling Acres that were brushed a decade ago usually show it first around the cutlery drawer, which is exactly the wear zone spraying survives best.
Why Sprayed Cabinet Painting Lasts Longer Than Brushed Work
An even film cures evenly. A brush lays paint on thick in some places and thin in others, and the thick places stay soft for weeks while the thin places wear through early. Sprayed cabinet painting puts down two or three uniform passes, each one sanded lightly before the next, so the whole film hardens at the same rate.
The visible difference is texture. Brushed doors carry stroke lines along the stiles and stipple in the panel. Sprayed doors carry neither. The durability difference shows later, at the handles and the corners, where sprayed cabinet painting holds an edge that brushed work has already chipped.
Which Cabinet Painting Happens Off Site And Which Happens In The Kitchen
Doors, drawer fronts and loose shelving all travel to the shop. They are sprayed lying flat, which lets the coating level out under gravity instead of sagging down a vertical face, and they cure in controlled air rather than in a July kitchen at sixty percent humidity.
Boxes and face frames cannot leave, so containment comes to them. Plastic seals the room, floors and counters are covered, extraction pulls air out, and the cabinet painting happens with the kitchen closed off for one to three days. Condo buildings get a shorter version of this, and condo kitchens have their own page.
Dust control matters as much as the gun does. Sanding runs with vacuum extraction at the tool, the room is wiped down before the first coat goes on, and the containment stays up between coats so nothing settles into a wet film. Cabinet painting that picks up grit on the second coat has to be flattened back and sprayed again.
Which Cabinet Painting Coatings Are Sprayed And How Long They Cure
Two families cover almost every job. Waterborne alkyd enamels flow out well, hold colour and cure to full hardness over about thirty days while being usable in a week. Two-component polyurethanes, the Italian wood coatings used across Ontario shops, mix with a hardener and reach full cure inside a day, with better chemical and wear resistance.
Both are low-VOC and neither of them is ever brushed. The choice is made against the kitchen. A house with three children and a busy range gets the harder film. A quiet kitchen getting a warm white gets the enamel, which is more forgiving to touch up later. Cabinet painting done in either system is named in the quote before a door comes off.
Ask What Sprayed Cabinet Painting Would Cost On This Kitchen
The visit is free and the written quote spells out the coating, the number of coats and the price. Spray work is quoted by the piece, so a door count is the fastest way to get an honest cabinet painting number.
Call +1 (289) 201-5986 to book a look, or send the details through the contact form. Every other kind of cabinet painting is listed on the home page.
Cabinet Spray Painting Questions
Is spraying better than brushing cabinets?
Yes. A brush lays paint on thick in some places and thin in others, so the film cures unevenly. Spraying puts down two or three uniform coats with a light sand between each, so the whole film hardens at the same rate and holds its edges at the handles.
Which coatings are sprayed?
Either a waterborne alkyd enamel, which is usable in a week and fully hard in about thirty days, or a two-component polyurethane, which cures inside a day with better wear resistance. Both are low-VOC. The product is named in the quote before a door comes off.
How is dust kept out of the finish?
Sanding runs with vacuum extraction at the tool, and the room is wiped down before the first coat goes on. Containment stays up between coats so nothing settles into a wet film. Doors sprayed in the shop booth get filtered air as well.